Heart and Flowers Pop Up Box Card Tutorial

I designed a Pop Up card in the shape of a heart filled with flowers.

With my Mum's 89th birthday coming up I knew it would be perfect to send to her. A special card which would be just right for her to display on her shelf and no upkeep or watering of the flowers would be necessary.

The photo of my Mum's card is the one below and is my original design:

The card got posted out and I shared a photograph of it with some crafty friends on facebook.

I hadn't expected anyone to ask me for a tutorial - - but someone did.

Yowzer!!!

Well, what better way to do this than to make the card all over again (which is the monochrome version at the top), take lots of photos, write a few words and put the tutorial here. It will be my very first blog tutorial, so there will be plenty of room for improvement, that's for sure.

Right then.. .. . Better get on with it......

1.  Start by die cutting 2 heart shapes from sturdy card. I used 270gms black card. 

VERY IMPORTANT: There are many different heart shape dies on the market and the measurement for the inner box is specific to the die I used. 

The die I used was a scalloped edge nesting heart by X-Cut and it was the largest in the set, measuring 10.5 cms in width. It isn't a problem to use a different shape heart, but you will need to measure the width and depth and possibly adjust the depth and width of the inner box to fit, so that it doesn't protrude at the sides, if necessary. 

2.  Cut a straight edge along the bottom left of both hearts (lay one heart on top of the other and cut at the same time, so that they are even).

3.  Cut 2 strips of card measuring 13.5 cms x 4 cms.

4.  Score both strips at 4 cms and at 12 cms. The end bit forms a tab to glue both strips together.

5.   Cut 2 shorter strips measuring 10 cms x 3.5 cms.

6.   Score these shorter strips at 1 cm in from each end, to form tabs.

7.   Glue the larger inner box strips together to form the box shape as shown in the photo above.

8.   Fold in the tabs of the shorter strips as shown above.

Next comes the slightly tricky part. ... ....  . ... .

9.   Glue the tabs of the short strips and insert them spaced as evenly as possible into the box.

This can be a bit fiddly to do. I used wet glue to allow wiggle room. You need to check that the inner box piece will flatten down without being distorted and open back to its box shape again. This is what makes it possible to flatten the card for posting.

10.  Glue one of the larger sides of the inner box to one of the hearts, exactly as shown in the photo above.

11.  Now glue the other heart to the front of the box. Make sure the hearts are lined up.  When the heart "box" stands on its base, it should look like the one in the photo above.

That completes the main structure. All that's left to do now is fill it with paper flowers and maybe even some foliage.

12.   Die cut several flowers from normal card (about 160 gms). I used a ball tool to emboss the petals and give them a more natural shape.

13.  Glue each flower to a strip of acetate with a hot glue gun. My acetate strips were about 12.5 cms long to start with.

FINALLY.  ....

Arrange and hot glue the bottom of the acetate strips to the black card struts of the inner box. Cut the acetate strips at different lengths, as required, to get a nice arrangement. Keep checking that the heart box will still fold down flat and that it stands nicely along tbe flat base.

Decorate the main part of the heart box to your liking.

IMPORTANT NOTE: The design of the heart and flower box is deliberately intended to look as if it is tilted - - for a unique flower arrangement. When you are glueing in any elements whatsoever with the acetate strips you will need to take this into account.

My card flattened down nicely enough to fit into an 8 inch square envelope. Or you could make a box to fit, if you wanted.